Canadian Spa Control Panel Instructions

Canadian Spa Control Panel Instructions. Step 1:turn off the power to the spa. Pull the cover off the control panel.

How to fit your new Hot Tub Control Panel HotTubDIY.co.uk from www.hottubdiy.co.uk

Turn the power off for one hour and then turn it back on. Reset the control panel if it only displays dashes and not error messages. If the panel has a single temperature button, pressing the button will cause the temperature to flash.

Download Image

Source: transportbehaelter.com

Exact rating will appear on unit’s metal id tag. Do not permit any electrical appliance, such as a light, telephone, radio, television, etc. If required, the easytouch indoor control panel can be password protected. To access a password protected control panel, simply enter the four digit assigned password (see page 47).

Download Image

Source: www.hottubdiy.co.uk

Step 1:turn off the power to the spa. Canadian installations must be at least three (3) meters (10 feet) from the water. Canadian installations solid copper conductor between this unit and any metal equipment, metal enclosures or electrical equipment, metal water pipe, or conduit within 5 feet. Prior to performing any service to the spa package turn off all primary electric power at the main circuit breaker or disconnect panel.

Download Image

Source: www.arcticspas.com

Also, push the “jets 2” or “aux” button, if you have a 2nd pump, to turn it on. To access a password protected control panel, simply enter the four digit assigned password (see page 47). Canadian installations solid copper conductor between this unit and any metal equipment, metal enclosures or electrical equipment, metal water pipe, or conduit within 5 feet. Opening the front cover of the electrical control box can make all field electrical connections.

Download Image

Source: www.manualsdir.com

Refer to the manual to identify the configuration of your spa. Pressing a temperature button again will adjust the set temperature in the direction indicated on the button. Be sure to open all valves and jets in the plumbing system before fi lling to allow as much air as possible to escape from the plumbing and the control system during the fi lling process. Reset the control panel if it only displays dashes and not error messages.

Download Image

Source: www.arcticspas.com

User can set temperature, filtration cycle and mode through the console. Canadian installations solid copper conductor between this unit and any metal equipment, metal enclosures or electrical equipment, metal water pipe, or conduit within 5 feet. Using the outdoor control panel buttons you can manually override any automatic settings. For more information, refer to the easytouch user’s guide (p/n 520584).

Download Image

Source: picclick.co.uk

When the lcd stops flashing, the spa will heat to the new set temperature when required. Please refer to the spa user manual to identify the configuration of your spa. Prior to performing any service to the spa package turn off all primary electric power at the main circuit breaker or disconnect panel. Reset the control panel if it only displays dashes and not error messages.

Download Image

Source: tyanheol.com

Be sure to open all valves and jets in the plumbing system before fi lling to allow as much air as possible to escape from the plumbing and the control system during the fi lling process. +49 (0)2203 806 4038 schwammenaueler str 27, 52396 heimbach, germany ca: After allowing the display to stop flashing, pressing Children should not use spas or hot tubs without adult supervision.

Download Image

Source: picclick.com

Fill the spa to its correct operating level. Please refer to the spa user manual to identify the configuration of your spa. After allowing the display to stop flashing, pressing Be sure to open all valves and jets in the plumbing system before filling to allow as much air as possible to escape from the plumbing and the control system during the filling process.

Download Image

Source: porchandprairie.com

To access a password protected control panel, simply enter the four digit assigned password (see page 47). Turn the power off for one hour and then turn it back on. All controls or devices accessible from the spa must be powered by a maximum of 12 vdc. Depending on your spa configuration, control up to 2 pumps, a blower and a light system.

Download Image

Source: www.spatex.com.au

Pull the cover off the control panel. Be sure to open all valves and jets in the plumbing system before filling to allow as much air as possible to escape from the plumbing and the control system during the filling process. Pressing a temperature button again will adjust the set temperature in the direction indicated on the button. Refer to the manual to identify the configuration of your spa.

Download Image

Source: proreviewerblog.com

Using the outdoor control panel buttons you can manually override any automatic settings. Refer to the manual to identify the configuration of your spa. Do not use spas or hot tubs unless all suction guards are. Remove cabinet panel, and covering for the control system.

Download Image

Source: wiring121.blogspot.com

Contact your local retailer if you are unable to download or view the. Please refer to the spa user manual to identify the configuration of your spa. For more information, refer to the easytouch user’s guide (p/n 520584). Remove cabinet panel, and covering for the control system.

Download Image

Source: tuwir.ueuo.com

Using the control panel prevent access to the spa. If the panel has a single temperature button, pressing the button will cause the temperature to flash. If you know that there is a way to soft boot or soft reset your control panel then try this first if it has crashed but the most likely thing that will work is if you switch it off and then on again. Within 5 feet (1.5 m) of a hot tub.

Pressing The Button Again Will Cause The Temperature To Change In One Direction (E.g.

Suggested size will ensure proper operation. ** the location of the control system may vary depending on the model of hot tub, but the topside and control system will always be on the same side of the tub. Do not permit any electrical appliance, such as a light, telephone, radio, television, etc.

Also, Push The “Jets 2” Or “Aux” Button, If You Have A 2Nd Pump, To Turn It On.

After allowing the display to stop flashing, pressing Pull the cover off the control panel. Remove cabinet panel, and covering for the control system.

Press The Spa Button To Activate The Filter Pump, Rotate The Pool/Spa Valve Actuators And Circulate The Spa Water (Led On).

If required, the easytouch indoor control panel can be password protected. Be sure to open all valves and jets in the plumbing system before filling to allow as much air as possible to escape from the plumbing and the control system during the filling process. Children should not use spas or hot tubs without adult supervision.

Do Not Use Spas Or Hot Tubs Unless All Suction Guards Are.

If you remove the cabinet panel shown in the picture below you will reveal the control system. User can set temperature, filtration cycle and mode through the console. Exact rating will appear on unit’s metal id tag.

When Using A Panel With Up And Down Buttons (Temperature Buttons), Pressing Up Or Down Will Cause The Temperature To Flash.

Turn the power off for one hour and then turn it back on. Depending on your spa configuration, control up to 2 pumps, a blower and a light system. Press the button again to switch the filter pump off (led off).